Can a 40-Footer Truck Reach Your Factory? Road, Gate, Turning Space and Loading Bay Checks in Rawang, Serendah and Shah Alam
Usually yes in a planned estate, but measure it. Selangor's planning manual gives industrial service roads a 66 ft (20.1 m) road reserve, and PLANMalaysia sizes a trailer bay at 4 m by 18 m plus 18.3 m to manoeuvre, 36.3 m in all. At a viewing I measure tarmac, gate opening, yard depth, dock and canopy headroom.
Key Takeaways
- A 40 ft container is 12.192 m long, 2.438 m wide and 2.591 m tall (2.896 m for a high cube), and a 20 ft box is 6.058 m long, per the ISO 668 table in Hapag-Lloyd's container specification. Both arrive on a trailer behind a tractor unit, so plan access for the trailer, not the box.
- PLANMalaysia's parking guideline sizes a trailer bay at 4 m by 18 m and adds 18.3 m of manoeuvring space, 36.3 m of clear length in all, and asks for at least 4.5 m of headroom under a canopy on a flat platform (PLANMalaysia parking guideline).
- Selangor's planning manual gives industrial service roads a 66 ft (20.1 m) road reserve and side or back lanes 40 ft (12.2 m). A reserve includes drains and verges, so I measure the tarmac and the gate, not the plan figure (Selangor planning manual).
- Terrace rows were planned with one lorry bay for every five units, so at a terrace factory a 40-footer normally loads from the road. Detached and semi-detached plots are where a trailer can turn inside the fence.
- Changing a gate, a fence or a drain crossing needs the council: MPS in Rawang, MPHS in Serendah, Bukit Beruntung and Batang Kali, MBSA in Shah Alam. Agree in the lease who applies and who pays.
How big is a 20 ft or 40 ft container, and why plan for the trailer instead?
A common assumption is that bringing in only 20-footers solves access. It does not. A 20 ft box is half the length of a 40 ft one, but it still comes on a trailer behind a tractor unit, and the turning path of that combination decides whether it gets through your gate. The box size matters later, at the dock, when a forklift has to drive into it.
These are the ISO 668 figures as printed in Hapag-Lloyd's container specification:
| Container | External length | External width | External height | Minimum door opening (width x height) |
|---|---|---|---|---|
| 20 ft standard | 6.058 m | 2.438 m | 2.591 m | 2.337 m x 2.261 m |
| 40 ft standard | 12.192 m | 2.438 m | 2.591 m | 2.337 m x 2.261 m |
| 40 ft high cube | 12.192 m | 2.438 m | 2.896 m | 2.337 m x 2.565 m |
| 45 ft high cube | 13.716 m | 2.438 m | 2.896 m | 2.337 m x 2.565 m |
Two numbers from that table matter at a viewing. The height: a high cube is 2.896 m tall before the trailer deck lifts it, which is why canopy headroom matters. The door opening: about 2.34 m wide, so the forklift you use to stuff or unstuff the box has to fit through it, mast and all.
How wide should the road be for a 40-footer in Rawang, Serendah or Shah Alam?
Most planned estates in my areas were approved under Selangor's planning standards. The Selangor planning manual published by PLANMalaysia@Selangor (third edition) sets these figures for industrial areas:
- service roads: 66 ft (20.1 m) road reserve
- side lanes and fire breaks: 40 ft (12.2 m)
- back lanes: 40 ft (12.2 m)
- dead ends to be avoided; where a cul-de-sac cannot be avoided, no longer than 623 ft (189.9 m), with a turning circle more than 100 ft (30.5 m) across
- the main access into an industrial area should not run through housing
PLANMalaysia's parking guideline adds that parking for large lorries and trailers should connect to a main road with a reserve of at least 30.5 m, preferably a dual carriageway (PLANMalaysia).
A road reserve is not the driving width. The same Selangor manual's road table gives lanes of 3.0 m or 2.75 m for urban local roads (classes U3 and U2), so once drains, verges and footpaths come out of a 66 ft reserve, a two-lane estate road can have far less tarmac than the plan suggests. Lorries parked on both sides narrow it again. That is why I measure kerb to kerb myself.
Before a client visits, I drive the route from the expressway exit to the gate at the hours their trucks would run. I look for tight junctions, low structures, roads through housing and stretches where parked trailers leave a single lane. In Rawang and Serendah that drive starts at the North-South Expressway exit the haulier would use; for Kundang it is the LATAR expressway, which I cover in my Kundang warehouse guide. In the older Shah Alam sections I note how many lorries park on the street during the day, because that is what the driver will meet.
How much space does a 40-footer need to turn and park inside the gate?
The clearest benchmark I have is the bay table in PLANMalaysia's parking guideline:
| Vehicle | Bay width | Bay length | Manoeuvring space | Total length needed |
|---|---|---|---|---|
| Small lorry | 3 m | 6 m | 6 m | 12 m |
| Large lorry | 4 m | 15 m | 15.3 m | 30.3 m |
| Trailer | 4 m | 18 m | 18.3 m | 36.3 m |
The guideline recommends at least two loading spaces so trucks do not queue at one, treats any vehicle with a laden weight above 5,000 kg as heavy, and says the turning area for each bay angle should follow JKR's road design standard, Arahan Teknik Jalan 8/86 (2015 amendment). Selangor's manual is close: a loading area of at least 30 ft by 26 ft (9.1 m by 7.9 m), and a trailer bay of 14 ft by 59 ft (4.26 m by 17.9 m) plus 18 m for handling (Selangor planning manual).
In practice I read that as follows: if the trailer has to reverse straight onto a dock, I want roughly 36 m of clear, level yard in front of the dock face, measured from the dock to the gate line or to whatever would stop the truck. With less, the driver has to start the reverse from the public road, which some estates tolerate and some neighbours do not.
The same standards also show which buildings were designed with trailers in mind:
- Detached and semi-detached factories: the Selangor manual asks for one lorry bay per 10,000 sq ft (929.9 sq m) of floor area or at least two, a 40 ft (12.2 m) setback facing the road and 25 ft (7.6 m) at the sides and rear. The front setback is where a trailer usually waits; a 25 ft side setback works as a driveway, not a turning area.
- Terrace factories: one lorry bay for every five units, on a minimum lot of 20 ft by 80 ft (6.1 m by 24.4 m). A 59 ft trailer bay does not fit inside such a lot together with the building, so containers are loaded from the road. I explain what that means in a row like Bukit Beruntung in my terrace factory checklist.
If a 40-footer every day is part of your operation, start with detached factories for rent in Rawang or warehouses for rent in Shah Alam rather than terrace stock.
What should the gate and the loading bay measure?
I have not found a single gate-width figure in the Selangor manual, and the right width depends on the road in front: the narrower the carriageway, the wider the gate has to be, because the trailer cannot swing out before it turns in. So I measure what is there and test it against how trucks actually turn:
- Clear gate opening: between the posts with the gate fully open, not the width of the gate leaf. Sliding gates often leave a post or the end of the track inside the opening.
- The drain crossing: many factories in my areas sit behind a roadside drain, and the concrete crossing is often narrower than the gate. A trailer's rear wheels cut inside the turn, so broken drain covers, chipped kerbs and tyre marks on the verge tell you trucks are struggling.
- Anything overhead: gate arches, guardhouse roofs, pipe racks and cables crossing the driveway.
- Canopy headroom: PLANMalaysia asks for at least 4.5 m under a canopy on a flat platform and 4.75 m on a ramp. A high cube alone is 2.896 m tall before the trailer deck.
- The dock: whether the dock height suits the trailers your haulier uses (ask them for their deck height), whether there is a dock leveller, and whether the roller shutter's clear width and height let a loaded forklift through.
- Lighting: the guideline asks for at least 100 lux at covered loading areas and 50 lux in the open, which matters if your containers arrive at night.
What do I measure at a viewing?
I bring a laser measure, a tape and the approved plans if the owner has them. This is the sheet I fill in:
| Check | What I measure or ask |
|---|---|
| Route | Drive from the expressway exit at truck hours; note junctions, low structures and housing |
| Road in front | Tarmac width kerb to kerb, and how many lorries park there during the day |
| Gate | Clear opening with the gate fully open, post positions, sliding track, overhead items |
| Drain crossing | Width, condition of the corners, damaged covers |
| Yard | Clear length from dock face to gate line (benchmark 36.3 m for a trailer), slope, ponding, cracks |
| Headroom | Lowest point of the canopy at the dock (benchmark 4.5 m flat, 4.75 m on a ramp) |
| Dock and shutters | Dock height, leveller, shutter clear width and height |
| Bays | How many trailers can load at once and where the next one waits |
| Papers | Approved layout plan showing the loading area, the CCC, any council permit for gate or fence changes |
I also ask the landlord one question: do 40-footers deliver here now, and which way do they come in? An owner who has loaded containers for years knows the answer. If the answer is vague, I suggest the client's haulier sends a driver to look before any deposit is paid.
Can the gate be widened, and who approves it in Rawang, Serendah and Shah Alam?
Often it can, but it is a permit, not a weekend job: the fence, the drain and the road reserve all fall under the council.
- Rawang (Majlis Perbandaran Selayang, MPS): MPS's minor works permit lists changes to an existing fence or wall. A new fence or wall goes through a qualified submitting person with a detailed fence plan, at up to 1.8 m high, and the form asks for a copy of the CCC (Form F) and the latest assessment bill, with a RM100 processing fee and a RM5 sticker (MPS form JB B08).
- Serendah, Bukit Beruntung and Batang Kali (Majlis Perbandaran Hulu Selangor, MPHS): a permanent fence on a non-residential lot goes through a qualified submitting person, with a comment letter from MPHS's Engineering Department on entrances and drains. The 2026 checklist sets a RM70 processing fee, a one-off permit fee of RM6 per metre of fence on industrial land, a RM1,000 refundable plan deposit and a RM20 sticker. A fence built before approval is charged ten times the permit fee, and a tenant must attach the tenancy agreement (MPHS fence checklist).
- Works on the council road need a road works permit. MPHS's form PT-1 is issued under the Road Works By-laws 1996 made under Act 133 and is submitted by a qualified person (MPHS form PT-1). Its checklist is written for trenches and utility crossings, so ask the Engineering Department which permit a wider drain crossing needs.
- Shah Alam (Majlis Bandaraya Shah Alam, MBSA): the Shah Alam sections fall under MBSA, and I have the owner's consultant confirm with MBSA what has to be submitted before we agree any change.
In the lease I write down who applies, who pays the consultant and the fees, and whether the tenant must put the original gate back at the end.
For registered factory prices around these estates, see FactoryHub's Rawang industrial transactions, and for the same question answered nationally, FactoryHub's container truck access guide. Area overviews are on my Rawang, Serendah and Shah Alam pages.
Loading bays and lorry parking
What is a factory loading bay in Rawang or Shah Alam?
A loading bay is where a lorry or trailer stops to load and unload, and at a Rawang or Shah Alam factory it has to fit the whole trailer, not only the container. PLANMalaysia's guideline sizes a trailer bay at 4 m by 18 m, with another 18.3 m to manoeuvre, 36.3 m in total. Also check the dock height, the headroom under the canopy and the clear gate opening against what MPS or MBSA requires.
How many loading bays does a factory in Serendah or Shah Alam need?
It depends on how many trucks you move, but PLANMalaysia recommends at least two loading spaces so trucks do not queue for one. Selangor's planning manual asks detached and semi-detached factories for one lorry bay per 10,000 sq ft of floor area, with a minimum of two, while terrace rows were planned with one bay for every five units. Check the approved layout with MPHS or MBSA.
How many lorries can park at a factory in Rawang or Serendah at the same time?
There is no fixed number; it depends on the size of the yard and the approved layout. PLANMalaysia sizes a trailer bay at 4 m by 18 m plus 18.3 m to manoeuvre, so each trailer needs roughly 36.3 m of clear length. For detached factories, Selangor's manual asks for one lorry bay per 10,000 sq ft, with at least two. Check the approved plan with MPS or MPHS.
Related questions, answered in detail on FactoryHub
- Does a factory need a Dock Leveler? Not every factory needs one, but a dock leveller is needed where goods are loaded and unloaded at a raised loading bay.
- What size Roller Shutter does a factory need? Size the roller shutter to the loading bay and to how container trucks reach it, so check the bay size, turning radius and apron depth for 20 ft and 40 ft trucks.
- How many Loading Bays does an e-commerce warehouse need? It depends on your order volume and how fast trucks turn around, so work it out together with Grade A specifications, sprinklers and any automation you need.
- What building specifications are needed for future logistics warehouses? Before renting or buying a logistics, 3PL or e-commerce warehouse in Malaysia, check the loading bays, clear height, floor loading and truck access.
- What are the standards for a Grade A Warehouse? Grade A specifications cover loading bays, sprinklers and automation, plus location factors such as how close the warehouse is to Port Klang for e-commerce and 3PL use.
These questions are answered in full on FactoryHub.
To have a factory or warehouse in Rawang, Serendah or Shah Alam checked for 40-footer access before you sign, WhatsApp Jason Low (Probationary Estate Agent PEA 1478, CID Realtors Sdn Bhd E(1) 1855) on +60 12-288 1834.
Questions people ask
01What is the length of a 40 ft container truck?+
The container itself is 12.192 m long, and a 20 ft box is 6.058 m, under ISO 668. For parking and loading, PLANMalaysia's guideline plans a trailer bay 18 m long and 4 m wide, with another 18.3 m to manoeuvre. I use 36.3 m of clear yard in front of a dock as the benchmark when I view a factory.
02How wide must the road be for a 40-footer to reach a factory in Selangor?+
Selangor's planning manual gives industrial service roads a 66 ft (20.1 m) road reserve and side and back lanes 40 ft (12.2 m). PLANMalaysia adds that trailer parking should connect to a main road with a reserve of at least 30.5 m. A reserve includes drains and verges, so measure the tarmac kerb to kerb and allow for lorries parked on the street.
03Can a 40-footer load at a terrace factory?+
Usually only from the road. Selangor's manual planned terrace rows with one lorry bay for every five units on lots as small as 20 ft by 80 ft, and a 59 ft trailer bay does not fit inside such a lot with the building. If containers arrive daily, look at detached or semi-detached factories instead.
04What headroom does a loading bay canopy need for container trucks?+
PLANMalaysia's parking guideline asks for at least 4.5 m of headroom on a flat platform and 4.75 m on a ramp. A high cube container alone is 2.896 m tall before the trailer deck lifts it. Measure the lowest point under the canopy, including lights, gutters and pipes.
05Do I need council approval to widen a factory gate in Rawang or Serendah?+
Yes. In Rawang, MPS handles fence and wall changes through its minor works permit (RM100 processing and a RM5 sticker), and a new fence goes through a qualified submitting person. In Serendah, Bukit Beruntung and Batang Kali, MPHS charges RM6 per metre of fence on industrial land plus a RM70 processing fee and a RM1,000 refundable deposit, and works on the council road need a separate road works permit.
06Which industrial areas in Rawang, Serendah and Shah Alam can 40-foot container trucks enter?+
Most planned industrial estates in Rawang, Serendah and Shah Alam can take a 40-footer, but every site still has to be measured. Selangor's planning manual gives industrial service roads a 66 ft (20.1 m) road reserve, and that reserve includes drains and verges, so measure the tarmac from kerb to kerb. Detached and semi-detached factories suit trailers. Terrace rows were planned with one lorry bay for every five units, so containers there are loaded from the road.
07How far should a factory in Rawang or Serendah be from the highway for 40-foot trucks?+
The planning standards set no fixed distance, and the route matters more than the kilometres. Before a viewing I drive from the expressway exit the haulier would use to the gate, at the hours the trucks run, and look for tight junctions, low structures, roads through housing and streets where parked trailers leave a single lane. For Rawang and Serendah that drive starts at the North-South Expressway exit; for Kundang it is the LATAR expressway.
08How do you determine whether a factory in Rawang or Shah Alam is suitable for large-scale logistics transport?+
Measure the route, the road, the gate and the yard against the size of a trailer. A 40 ft container is 12.192 m long, a high cube is 2.896 m tall, and PLANMalaysia plans a trailer bay at 36.3 m of length in total. In Rawang and Shah Alam, drive the route at truck hours, measure the tarmac, the clear gate opening and the headroom at the dock, and confirm what MPS or MBSA requires.
Sources
- Hapag-Lloyd, Container Specification (ISO 668 external dimensions and door openings)
- PLANMalaysia, Garis Panduan Perancangan Tempat Letak Kenderaan GP0011-A (2017)
- PLANMalaysia@Selangor, Manual Garis Panduan dan Piawaian Perancangan Negeri Selangor, Edisi Ketiga
- Majlis Perbandaran Hulu Selangor, Senarai Semak Permohonan Pagar Kekal (Selain Lot Kediaman) 2026
- Majlis Perbandaran Hulu Selangor, Borang PT-1 Permit Kerja Di Jalan
- Majlis Perbandaran Selayang, Borang JB B08 Permit Kerja-Kerja Kecil (Bukan Strata)
- FactoryHub, Rawang industrial transactions (JPPH-registered)
Units on the market nearby
Semi-D Factory for Rent in Saujana Teknologi Rawang, Rawang, 6,525 sq ft
RM 10,500/month
Semi-Detached Factory for Sale or Rent in Saujana Rawang, Rawang, 8,000 sq ft
RM 4,000,000 · RM 15,000/month
Detached Factory for Rent in Batu 17 Rawang, 9,000 sq ft
RM 21,000/month
More on power, height, floor and access
- How Much Power Does Your Factory Need? kVA to Amps From the Machine List, Checking the Unit and a TNB Upgrade in Rawang, Serendah and Shah Alam
- Factory Floor Loading in Rawang, Serendah and Shah Alam: What kN/m² Means and What I Check Before Machines or Racking Go In
- TNB Tariff 2026 for a Factory in Rawang, Serendah or Shah Alam: Which Rate the Unit Puts You On and How to Estimate the Bill Before You Sign
- TNB Compact Substation for a Factory in Rawang or Serendah: When You Need One and What to Check