Factory Floor Loading in Rawang, Serendah and Shah Alam: What kN/m² Means and What I Check Before Machines or Racking Go In
Floor loading is the weight a factory floor was designed to carry, in kilonewtons per square metre: 1 kN/m² is about 102 kg per square metre, so 10 kN/m² is roughly one tonne. Developer figures I checked run from 10 kN/m² (Serendah semi-detached) to 30 kN/m² (Elmina detached). Rely on the approved structural plans, not the brochure.
Key Takeaways
- Floor loading is a design figure, written in kN/m². One kN/m² is about 102 kg on every square metre, so 10 kN/m² is roughly one tonne per square metre. The original Selangor building by-laws print 10.0 kN/m² as 1,020 kgf/m² (Selangor UBBL 1986, original text).
- Published figures in my areas run from 10 to 30 kN/m². Serendah Technology Park's semi-detached factories state 10 kN/m², Elmina Business Park's Twin Factories 3 state 15 kN/m² for the warehouse area only, and its Masterpiece Plus detached factories state 30 kN/m² at the production area.
- The number that counts is on the approved structural plans. Selangor's by-law 16(3) requires structural plans to be clearly marked with the imposed load each floor was designed for (Selangor UBBL, updated text).
- Forklifts and machines are treated separately. By-law 60 requires special provision in the floor design where forklifts may be used, and by-law 68 requires an allowance of at least 20% for impact and vibration from installed machinery.
- A mezzanine needs the council's written permission first. Section 79 of the Street, Drainage and Building Act 1974 covers any gallery, loft, partition or similar structure added inside a building (Act 133).
What does floor loading in kN/m² actually mean?
A floor loading figure tells you how much imposed load the engineer allowed for on each square metre of floor. Imposed load means what you bring in: goods, machines, people and vehicles, not the weight of the slab itself. It is written in kilonewtons per square metre (kN/m²), which is the same unit as kilopascals (kPa).
Figures are often quoted in tonnes per square metre too, so I keep one conversion in mind. The original Selangor by-laws print both units side by side: 5.0 kN/m² as 510 kgf/m², 7.5 kN/m² as 765 kgf/m² and 10.0 kN/m² as 1,020 kgf/m² (Selangor UBBL 1986, Fourth Schedule). Using that ratio:
| Figure you are quoted | About kg per m² | About tonnes per m² |
|---|---|---|
| 5 kN/m² | 510 | 0.5 |
| 10 kN/m² | 1,020 | 1.0 |
| 15 kN/m² | 1,530 | 1.5 |
| 30 kN/m² | 3,060 | 3.1 |
The last two rows are my arithmetic from the by-law's ratio. Going the other way, a brochure that says "3 tonnes per m²" means roughly 29 kN/m².
A floor also has two limits, not one. The distributed figure covers weight spread evenly over the floor. The concentrated figure covers weight pressing on a small patch: the old Selangor schedule applied it over a 300 mm square and, for a 5.0 kN/m² factory floor, set it at not less than 4.5 kN (Selangor UBBL 1986). A rack upright on a small base plate, a machine foot or a forklift wheel is a concentrated load, so a floor can pass the distributed test and still be overloaded at one spot.
Forklifts add their own allowance. The Eurocode on imposed loads sorts forklifts into six classes by lifting capacity and multiplies the static axle load by a dynamic factor of 2.00 for solid tyres or 1.40 for pneumatic tyres, to cover the effects of acceleration and braking with a lifted load (EN 1991-1-1 briefing, European Commission JRC).
What floor loading do terrace, semi-detached and detached factories have here?
No law fixes one figure per factory type. Each developer's engineer chooses the design load, so I only quote figures the developer itself publishes. These are the ones I could open for projects in my areas:
| Project | Type | Published floor loading | Power |
|---|---|---|---|
| Serendah Technology Park, off Jalan Sungai Buaya, Serendah | 3-storey semi-detached, 9,790 and 11,780 sq ft built-up | 10 kN/m² (storage and production area) | 150A |
| Twin Factories 3, Elmina Business Park, Shah Alam | Semi-detached, 13,663 sq ft built-up | 15 kN/m² (warehouse area only) | 200A |
| Masterpiece Plus, Elmina Business Park, Shah Alam | Detached, 1 acre, from 24,000 sq ft built-up | 30 kN/m² at the production area, upgradable to 50 kN/m² at extra cost | 400A |
Serendah Technology Park is developed by Landmark Concord Resorts Sdn Bhd and sits about 1.2 km from the Sungai Buaya toll plaza (project site). Sime Darby Property also describes the floor loading of its earlier Detached Factories 1 and Twin Factories 3 at Elmina as customisable, starting from 15 kN/m² (Sime Darby Property press release).
For terrace factories I have not found a developer page in Rawang, Serendah, Kundang or Shah Alam with a figure I could verify. For a terrace unit, and especially an older one, the figure has to come from the plans. My Bukit Beruntung terrace factory checklist covers the other papers to ask for.
Two details in that table matter more than the headline number. First, the figure usually applies to one zone. Sime Darby's 15 kN/m² is for the warehouse area only, and Serendah Technology Park gives its 10 kN/m² for the storage and production area. Office floors above are designed to lower figures. Under the old Selangor schedule, offices for general use were designed for 2.5 kN/m², and filing and storage space in offices for 5.0 kN/m² (Selangor UBBL 1986). The current Eurocode range for offices is 2.0 to 3.0 kN/m² (JRC). That is why I tell clients not to put stock on the upper floor of a 1.5-storey terrace factory until the plans say that floor can take it.
Second, power and floor loading rise together in these three examples, but they are separate design choices, so check both. My TNB tariff guide covers the power side.
Which rules was my factory designed to?
The year the building plans were approved tells you which table the engineer worked from.
Plans approved before the 2012 amendment. The Selangor Uniform Building By-Laws 1986 had a Fourth Schedule of minimum loads. "Factories and similar buildings" were set at 5.0, 7.5 or 10.0 kN/m² "as appropriate", and storage at not less than 2.4 kN/m² for each metre of storage height (Selangor UBBL 1986). So an older factory should have been designed for at least 5.0 kN/m², but which of the three figures the engineer chose is only visible on its plans.
Plans approved after the 2012 amendment. Sel.P.U. 142/2012 deleted the Fourth Schedule, and by-law 59 now says all imposed floor loads are calculated in accordance with MS EN 1991-1-1, the Malaysian edition of the Eurocode (Selangor UBBL, updated). In the base Eurocode, storage areas (category E1) carry 7.5 kN/m², while industrial use (category E2) has no fixed figure in that table and is set for the particular project (JRC).
Three by-laws apply whatever the date:
- By-law 16(3): structural plans must be clearly marked to show the imposed loads each floor system or part was designed for.
- By-law 60: where forklifts or other mechanical stacking machines may be used, the floor design must make special provision for them.
- By-law 68: loads from machinery, cranes and other plant must allow for dynamic effects, the increase for installed machinery must be at least 20%, and the design must also cover equipment loads while it is being installed or moved for servicing (Selangor UBBL, updated).
Floor loading is also a different question from whether the land is zoned for light, medium or heavy industry. Ms Teh explains those classes in her light, medium and heavy industry guide.
How do I check the floor before installing heavy machines or racking?
When a client gives me a machine list or a racking plan, I work in this order:
- Ask for the approved structural plans, not the brochure. Because of by-law 16(3), the load marking should be on them. I also ask for the CCC (Form F) or the older CF, so we know the building was certified.
- If the owner cannot find them, go to the council. In Rawang and Kundang the council is MPS. Its form JB-D06 lists the charges: RM20 to search, RM100 per set to inspect an approved plan, RM200 per set for a copy of a plan and RM100 for a certified copy. A tenant or buyer needs the owner's letter of consent, and the form notes that copies of a developer's approved development plans can only be requested by the developer or the submitting person it appointed (MPS form JB-D06). For Serendah, Sungai Choh, Bukit Beruntung and Batang Kali the council is MPHS, and for Shah Alam it is MBSA; ask their building department (Jabatan Bangunan) the same question.
- Write down what goes on the floor. For machines: weight, footprint, number and size of feet, and whether it vibrates or strikes. For racking: number of levels, pallet weight, upright loads and base plate size. For forklifts: class and tyre type. FactoryHub's floor loading calculator gives a first average figure in tonnes and kN per square metre, but it says itself that point loads from base plates, forklift wheels and machine feet need a structural engineer.
- Have a professional engineer compare the two. Only the engineer can say whether a slab designed for 10 kN/m² takes your rack uprights, or whether you need larger base plates, a different layout or strengthening.
- Walk the slab. On a site visit I look for cracks, uneven joints and patched trenches where a previous occupier cut the floor for pits or pipes, and I ask whether anything was cut or added after the CCC.
If you are buying a unit that is still being built, ask early. Sime Darby lists an upgrade from 30 to 50 kN/m² at additional cost for Masterpiece Plus, the kind of option that is simple at design stage and hard once the slab is cast.
Do I need council approval to add a mezzanine or racking?
For a mezzanine, yes. Section 79(1) of the Street, Drainage and Building Act 1974 says no one may erect any partition, compartment, gallery, loft, roof, ceiling or other structure in a building without the local authority's prior written permission. The owner is presumed to have done the work unless proved otherwise, and the council may remove the structure and charge the owner. Section 70(11) adds a fine of up to RM25,000 for altering a building without permission, and a court can order the building altered or demolished (Act 133).
Each council puts this into its own forms:
- MPS (Rawang, Kundang): its checklist for additions and alterations to industrial buildings, submitted through OSC 3.0 by the submitting person, asks, where relevant, for a set of structural plans and calculations with a covering letter from the structural engineer and Form A (MPS checklist JB-B01(B)). It also lists a separate annual permit for additions to factories (MPS building forms).
- MBSA (Shah Alam): its development FAQ says even a partition wall in a commercial or industrial building needs a temporary building permit, citing section 79 (MBSA FAQ).
- MPHS (Serendah, Sungai Choh, Bukit Beruntung, Batang Kali): it publishes checklists for additions and alterations, and for minor works on non-residential buildings (MPHS forms).
Developers sometimes plan ahead for a mezzanine. The Masterpiece Plus page mentions a "convertible mezzanine floor for future expansion", and Serendah Technology Park leaves a double-volume space "for additional mezzanine floor or high-racking system". Neither page says that future floor is already approved, so I treat it as new work that needs plans.
Freestanding pallet racking is not named in section 79. I still have clients ask the council before they buy tall racking, because racking and mezzanines can also change the fire certificate position. My Bomba fire certificate guide explains when the occupier must tell Bomba first.
What do I ask about floor loading on a site visit?
- Where exactly does the quoted figure apply: the whole ground floor, or only the warehouse or production zone?
- Is the figure on the approved structural plan, or only in a brochure?
- Has anyone added a mezzanine, cut the slab or changed the use since the CCC, and was it approved?
- Where will the heaviest machine stand, and is that spot near a slab joint or an old trench?
- Which forklift will run on the floor, and on which tyres?
For what factories here have actually sold for, FactoryHub keeps the registered JPPH transactions. More on each place is on the Rawang, Serendah, Kundang and Shah Alam pages, with current units on the factory page.
Related questions, answered in detail on FactoryHub
- How do you calculate how much weight a factory floor can bear? It is worked out as load per unit area, in kN/m², under the MS EN 1991-1-1 rules, and that figure is then checked against the racking and machine loads going on the floor.
- Can a factory floor with insufficient load-bearing capacity be reinforced? Yes. A floor that falls short on load capacity can be strengthened, including for presses, as part of floor repair and strengthening work.
- What specifications are needed for a heavy machinery manufacturing factory? It needs the right floor loading, power supply, crane capacity and zoning, and each of these should be checked before you buy or rent.
These questions are answered in full on FactoryHub.
To have the floor loading of a factory in Rawang, Serendah or Shah Alam checked before you sign, WhatsApp Jason Low (Probationary Estate Agent PEA 1478, CID Realtors Sdn Bhd E(1) 1855) on +60 12-288 1834.
Questions people ask
01What does floor loading mean for a factory?+
Floor loading is the imposed load, such as goods, machines and vehicles, that the engineer designed each square metre of floor to carry, usually written in kN/m². In Selangor, by-law 16(3) requires the structural plans to be marked with the load each floor was designed for. That marked figure, not a brochure, is the one to rely on.
02How do I convert tonnes per square metre to kN/m²?+
The original Selangor by-laws print 10.0 kN/m² as 1,020 kgf/m², so 1 kN/m² is about 102 kg per square metre. One tonne per square metre is therefore roughly 9.8 kN/m², and 3 tonnes per square metre roughly 29 kN/m².
03What floor loading do I need for pallet racking?+
There is no single figure, because racking presses on the slab through small base plates as concentrated loads. The old Selangor schedule required storage floors to take at least 2.4 kN/m² for each metre of storage height, and the base Eurocode puts general storage at 7.5 kN/m². Give the rack upright loads and base plate sizes to a professional engineer to check against the slab design.
04Do I need approval to build a mezzanine in a factory in Rawang, Serendah or Shah Alam?+
Yes. Section 79 of the Street, Drainage and Building Act 1974 requires the local authority's prior written permission for any gallery, loft, partition or similar structure inside a building. MPS's checklist for additions to industrial buildings includes structural plans and calculations from a structural engineer, and unapproved work can be removed at the owner's cost, with a fine of up to RM25,000 for altering a building without permission.
05Where do I find the floor loading of an existing factory?+
Start with the approved structural plans, which must show the design load of each floor. If the owner cannot find them, MPS charges RM100 per set to inspect an approved plan and RM200 per set for a copy, and a tenant or buyer needs the owner's consent letter. In MPHS or MBSA areas, ask the council's building department.
06Can I store goods on the upper floor of a 1.5-storey terrace factory?+
Only if the plans show that floor was designed for storage. Under the old Selangor schedule, offices for general use were designed for 2.5 kN/m² and filing and storage space in offices for 5.0 kN/m², and the Eurocode range for offices is 2.0 to 3.0 kN/m². Check the marking on the plans before moving stock upstairs.
Sources
- Selangor Uniform Building By-Laws 1986 (Sel.P.U. 26/1985), original text with the Fourth Schedule of imposed loads (KPKT JKT copy)
- Selangor Uniform Building By-Laws 1986, updated text including Sel.P.U. 142/2012: by-laws 16, 59, 60 and 68 (KPKT JKT copy)
- Street, Drainage and Building Act 1974 (Act 133), sections 70 and 79, reprint as at 1 June 2014 (Perbadanan Putrajaya copy)
- Use of EN 1991-1-1: densities, self-weight and imposed loads for buildings, N. Malakatas (European Commission JRC Eurocodes)
- Serendah Technology Park: 3-storey semi-detached factory floor plan and specifications
- Serendah Technology Park: project and developer information
- Sime Darby Property: Twin Factories 3, Elmina Business Park
- Sime Darby Property: Masterpiece Plus Collection detached factories, Elmina Business Park
- Sime Darby Property press release: 100% take-up for Detached Factories 1 and Twin Factories 3 in Elmina Business Park
- Majlis Perbandaran Selayang: form JB-D06, application for copies of documents and plans
- Majlis Perbandaran Selayang: checklist JB-B01(B) for additions and alterations through OSC 3.0
- Majlis Perbandaran Selayang: Building Department forms
- Majlis Bandaraya Shah Alam: development FAQ (partitions in commercial and industrial buildings)
- Majlis Perbandaran Hulu Selangor: downloadable forms (Building Department checklists)
- FactoryHub: floor loading calculator
- FactoryHub: registered JPPH industrial transactions
Units on the market nearby
Semi-D Factory for Rent in Saujana Teknologi Rawang, Rawang, 6,525 sq ft
RM 10,500/month
Semi-Detached Factory for Sale or Rent in Saujana Rawang, Rawang, 8,000 sq ft
RM 4,000,000 · RM 15,000/month
Detached Factory for Rent in Batu 17 Rawang, 9,000 sq ft
RM 21,000/month
More on power, height, floor and access
- How Much Power Does Your Factory Need? kVA to Amps From the Machine List, Checking the Unit and a TNB Upgrade in Rawang, Serendah and Shah Alam
- Can a 40-Footer Truck Reach Your Factory? Road, Gate, Turning Space and Loading Bay Checks in Rawang, Serendah and Shah Alam
- TNB Tariff 2026 for a Factory in Rawang, Serendah or Shah Alam: Which Rate the Unit Puts You On and How to Estimate the Bill Before You Sign
- TNB Compact Substation for a Factory in Rawang or Serendah: When You Need One and What to Check