Detached, Semi-D or Terrace Factory in Rawang, Serendah and Shah Alam: Land, Access, Power, Price and Which Suits Your Operation

Written by , PEA 1478 · Published · Updated · Choosing an area or industrial park

Short answer

Terrace (link) factories share both side walls, semi-Ds one wall, and detached factories stand alone with yard and setbacks all round. In JPPH-registered deals, terrace dominates the Serendah area, semi-D Rawang and Kundang; Shah Alam has all three. Choose by lorry access, power above or below 350 kVA and floor area, then compare prices within one type.

Illustration of an industrial street with a row of terrace factories, a pair of semi-detached factories and a detached factory with a container trailer in its yard.
Illustrative image

Key Takeaways

  • The type is about shared walls and the land left around the building. A terrace (link) factory shares walls on both sides, a semi-D shares one wall with its twin, and a detached factory stands alone. Selangor's 2016 planning manual set minimum lots of 20 ft x 80 ft for a terrace factory, 60 ft x 132 ft for a semi-D and half an acre for a small detached factory.
  • Each of my areas leans to one type. In JPPH-registered deals over 24 months, the Serendah area, which takes in Bukit Beruntung, recorded 256 terrace factories against 28 semi-D and 8 detached. Rawang and Kundang recorded 129 semi-D. Shah Alam was more even: 70 terrace, 66 semi-D and 20 detached.
  • Lorries separate the types early. The same manual asked every detached or semi-D lot for at least two lorry bays, but a terrace street for one lorry bay per five units. A trailer bay alone was sized at 14 ft x 59 ft, plus 18 m to manoeuvre.
  • Above 350 kVA, about 505A, TNB wants a new substation on land you hand over. That fits on a detached lot far more easily than on a terrace one.
  • A factory with 2,000 m² (about 21,528 sq ft) or more of floor fitted with automatic sprinklers needs a Bomba fire certificate. A typical terrace or semi-D unit sits well below that line; a large detached factory can cross it.

What makes a factory detached, semi-D or terrace on a Selangor plan?

People use the words loosely, and marketing names such as "cluster" or "link" factory add to it. So I go back to what the council approved. In Selangor the planning standards come from PLANMalaysia@Selangor's planning manual. Its third edition, approved by the state executive council in October 2016, is the last one I can quote in full, and its industrial chapter set these standards (Selangor planning manual, third edition, industrial chapter):

2016 manual Terrace (link) factory Semi-D factory Detached factory
Shared walls Both sides, one at the end of a row One, with its twin None
Minimum lot 20 ft x 80 ft (1,600 sq ft) 60 ft x 132 ft (7,920 sq ft) 0.5 acre (small) or 1 acre (medium to large)
Building cover Not set in the table Up to 60% of the lot Up to 60% of the lot
Setbacks and lanes 40 ft back lane; 40 ft side lane or fire break at row ends 40 ft facing a road; 25 ft at the sides and back 40 ft facing a road; 25 ft at the sides and back
Lorry parking 1 lorry bay per 5 units 1 per 10,000 sq ft of floor, at least 2 1 per 10,000 sq ft of floor, at least 2
Maximum height 40 ft Not set in the table Not set in the table

Every type was to face a 66 ft service road. In a detached or semi-D factory, up to 30% of the gross floor area may be treated as office space under the same table.

Two cautions. First, the manual has moved on: PLANMalaysia@Selangor lists a fourth edition approved in June 2022, and a new six-volume set of state planning guidelines, with industry as its own volume, approved on 7 November 2025 and confirmed on 12 November 2025. For a new building, your architect works from the current volume and the council's local plan. Second, for an existing factory what counts is the plan the council approved when it was built. That is why, whatever the type, I ask for the approved building plan and the CF or CCC before a viewing.

Which type will you actually find in Rawang, Serendah and Shah Alam?

Each town falls under a different council. The state's list of industrial areas by local authority puts Rawang's estates, among them Kawasan Perindustrian Rawang, Rawang Perdana, the PKNS parks at Batu 16 and Batu 20, Rawang Integrated, Saujana Teknologi Rawang and the Sunway managed park, together with Kundang and Kuang, under Majlis Perbandaran Selayang (MPS). Sungai Choh, Bandar Perodua Serendah, Batu 30 Serendah, Bukit Beruntung and Bandar Bukit Sentosa, and the MIEL and Selisek estates in Batang Kali come under Majlis Perbandaran Hulu Selangor (MPHS). Seksyen 15, 16, 23 and 26 (HICOM Industrial Estate), and HICOM-Glenmarie and Temasya in Seksyen U1, are under Majlis Bandaraya Shah Alam (MBSA).

The stock differs just as much. These are JPPH-registered transfers in the 24 months to August 2026, the records available so far, not every unit sold:

Registered deals in 24 months Terrace Semi-D Detached
Serendah area, including Bukit Beruntung 256 28 8
Rawang and Kundang 38 129 16
Shah Alam 70 66 20

This is how it shapes a search:

  • A small terrace unit on a tight budget. I start in Bukit Beruntung, the most active park in the Serendah records with 132 deals in 24 months. My Bukit Beruntung industrial area page lists the streets, and my terrace factory checklist for Bukit Beruntung covers the papers.
  • A semi-D. Rawang and Kundang give the most choice. The most active park in those records is Kota Elmina, with 104 deals in 24 months; see my Elmina Business Park page and the current semi-D factories for sale in Rawang.
  • A detached factory with real yard. Shah Alam's detached factories sit on the most land, a median of 67,901 sq ft in the records against 49,744 sq ft in the Serendah area and 26,215 sq ft in Rawang and Kundang. Serendah also has new plots at UMW HVM Park for owners who would rather build.

What do the registered prices and rents say for each type?

Every registered sale psf below is per sq ft of land, so compare it only within the same type. A detached factory carries a lot of yard, which makes its psf of land look low beside a semi-D even when the total price is far higher.

JPPH-registered sales, 24 months to August 2026 Terrace Semi-D Detached
Rawang and Kundang RM670,000; RM328 psf of land; 2,384 sq ft of land RM4.3 million; RM380 psf of land; 12,561 sq ft RM6.92 million; RM237 psf of land; 26,215 sq ft
Serendah area RM245,000; RM114 psf of land; 2,002 sq ft RM3.16 million; RM213 psf of land; 10,506 sq ft RM8.65 million; RM166 psf of land; 49,744 sq ft
Shah Alam RM1.13 million; RM484 psf of land; 2,002 sq ft RM5.92 million; RM514 psf of land; 10,779 sq ft RM16 million; RM335 psf of land; 67,901 sq ft

The prices are medians. Read along a row to see what the step from terrace to semi-D to detached costs in one place. Read down a column to compare places for one type: a semi-D is registered at RM213 psf of land in the Serendah area, RM380 in Rawang and Kundang and RM514 in Shah Alam.

Fewer tenancies are registered, so the rent picture is thinner:

Registered rents, 24 months Terrace Semi-D Detached
Rawang and Kundang RM1.06 psf/month; RM2,600 for about 2,400 sq ft (14 tenancies) No separate figure RM2.53 psf/month; RM12,500 for about 3,000 sq ft (7 tenancies)
Serendah area RM0.77 psf/month; RM1,500 for about 2,000 sq ft (20 tenancies) No separate figure RM1.06 psf/month; RM4,000 for about 4,160 sq ft (5 tenancies)
Shah Alam RM1.79 psf/month; RM4,400 for about 2,600 sq ft (46 tenancies) RM2.12 psf/month; RM17,300 for about 8,810 sq ft (24 tenancies) RM1.50 psf/month; RM12,200 for about 9,170 sq ft (34 tenancies)

Where a figure rests on fewer than ten tenancies I treat it as a rough pointer only. FactoryHub breaks the records down further for Rawang and Kundang, Serendah and Shah Alam.

Can lorries and 40-footers work at each type?

This is often where the choice is made. The 2016 manual sized a trailer bay at 14 ft x 59 ft (4.26 m x 17.9 m) with another 18 m to manoeuvre, and a small lorry bay at 10 ft x 20 ft with another 20 ft (industrial chapter). A trailer and its turning space therefore need about 36 m, roughly 118 ft, of depth, against an 80 ft minimum terrace lot. At a terrace factory a container is loaded from the road or the apron, on a street planned with one lorry bay for every five units. A semi-D or detached lot was planned to hold at least two lorry bays of its own.

On a viewing I check five things:

  1. The road. Whether it is a full 66 ft service road, and whether a trailer can turn at the junction without mounting the kerb.
  2. The gate and the apron. The gate width, and whether the space in front of the shutter keeps a trailer off the road while it loads.
  3. The surface. Whether the apron and yard are concrete that can take a loaded trailer, and how they drain after heavy rain.
  4. The neighbours. On a terrace street, whether their lorries and cars already fill the road when you need to load.
  5. The semi-D driveway. Which side the driveway runs on, and whether the twin shares the gate or the drive.

My notes on renting a factory in Rawang cover the other checks, and the Kundang guide on the LATAR Expressway covers access for warehouse traffic.

How much power can each type take from TNB?

TNB's Electricity Supply Application Handbook (ESAH 3.1) sets the minimum supply scheme by maximum demand. Buyers ask in amps, so I convert at 400V three phase:

Maximum demand About, in amps at 400V Minimum supply scheme in the handbook
Above 12 kVA to 100 kVA Up to about 144A Cable from the existing low voltage network, subject to TNB's study
Above 100 kVA to 350 kVA About 145A to 505A Cable from a feeder pillar or a new or existing substation, subject to TNB's study
Above 350 kVA to 1,000 kVA About 505A to 1,443A Direct underground cable from a new substation
1,000 kVA to below 5,000 kVA Above about 1,443A 11kV from a TNB switching station; extra land for a main intake substation may be needed

The handbook also asks an applicant for a load above 100A to appoint an electrical consultant engineer, and to provide substation land and building to TNB by transfer or lease at a nominal RM10. That is where the factory type bites. The 2016 planning manual lists an electricity substation among the structures allowed inside a building setback, so a detached lot has a place for one without losing floor. A terrace lot of about 2,000 sq ft has little ground to spare. So when a client's machines add up to more than 350 kVA, I search detached factories, or semi-D units that already carry the supply, and I ask for the latest TNB bill and the main switch rating before the viewing. My guide to TNB compact substations in Rawang and Serendah explains the substation plot in detail.

Which type suits which operation?

The way I match them, in general terms:

Operation Where I look first Why
Workshop, spare parts store, e-commerce packing, small food or light assembly line Terrace Low entry price, and a load the street network can usually carry
SME manufacturing with its own lorries and a small office Semi-D Own compound, at least two lorry bays in the planning standard, office up to 30% of the floor
Daily container traffic, machines above 350 kVA, a process that needs distance from housing, or more than 2,000 m² of floor Detached Yard, setbacks for a substation and fire engine access, room to extend within the 60% cover

Two rules push heavier users toward detached land. The first is distance from homes. The 2016 manual's buffer drawings show 50 m between light industry and housing, 150 m for medium industry and 300 m for heavy or high-risk industry, and note that the Department of Environment's guidelines set the measurement from time to time (industrial chapter). Many terrace streets in Bukit Beruntung and Rawang sit close to houses, which suits light work. Ms Teh's light, medium and heavy industry guide helps you place your process.

The second is Bomba. A factory of one storey or more becomes designated premises at 2,000 m² or more of total floor area fitted with an automatic sprinkler system, and a hazardous process is designated whatever its size (schedule under P.U.(A) 289/2020, as reproduced by Palcon). Designated premises need a fire certificate. A terrace unit on a 2,000 sq ft lot is far below the line, and a semi-D on about 10,500 sq ft of land at the 60% cover would need more than three full floors to reach it. A big detached plant can cross it, which my Bomba fire certificate guide explains.

What do I check on a viewing for each type?

Terrace factory

  • The approved plan against what stands: back extensions, roofed-over aprons, lofts and mezzanines.
  • The neighbours on both sides: what they make, the noise and smell, and how much they store against the shared walls.
  • The back lane: open and drained, or built over.

Semi-D factory

  • The twin: who occupies it and what they run, since you share a wall.
  • The boundary: whether the fence follows the title, and whether the driveway and gate lie wholly on your lot.
  • The supply: its own meter and its own rating, not a share of the twin's.

Detached factory

  • The setbacks: the manual lists what may stand there, such as a guard house, water tank, pump house, cooling tower, covered parking, LPG tank and electricity substation, or other structures the council approves. A store or canteen built into the setback without approval becomes the buyer's problem.
  • The sprinkler tank and pump room, a sign that the building may already be designated premises.
  • The yard: concrete that takes trailers, drainage, and room for lorries to queue at shift change.

More questions on detached, semi-D and terrace factories

In Rawang or Serendah, is it better to buy a detached factory or a semi-detached factory?

It comes down to your lorries and your power load. A semi-D shares one wall with its twin and was planned with at least two lorry bays, while a detached factory stands on its own with yard and setbacks on every side. Rawang and Kundang recorded 129 semi-D against 16 detached in JPPH-registered deals, so you will find far more semi-D units there. Before you buy, check the approved plan and CF or CCC with MPS or MPHS.

For investment in Shah Alam, is a detached factory or a semi-detached factory better?

That depends on your budget and the kind of tenant you want. Over 24 months, JPPH-registered medians in Shah Alam were RM5.92 million for a semi-D on 10,779 sq ft of land and RM16 million for a detached factory on 67,901 sq ft, with registered rents of RM2.12 psf a month for semi-D and RM1.50 for detached. Weigh the total price against the floor and yard your tenant will need, and check the title and approved use with MBSA.

What are the advantages and disadvantages of a detached factory in northern Selangor?

The advantage is space: a detached factory stands alone with yard and setbacks all round, which leaves room for trailers, a substation and later extensions within the 60% cover. The 2016 Selangor manual set a minimum lot of half an acre for a small one. The drawbacks are price and supply, since JPPH-registered deals in Rawang and Kundang show only 16 detached factories against 129 semi-D. Check the approved plan and CF or CCC with MPS or MPHS.

Why do large enterprises prefer detached factories in Shah Alam or Serendah?

Because a detached lot has room for heavy power, trailers and fire engine access. Above 350 kVA, about 505A at 400V, TNB requires a new substation on land the owner hands over by transfer or lease at a nominal RM10, and a detached lot can fit one within its setbacks. A large detached plant may also pass 2,000 m² of floor with automatic sprinklers, the point at which a Bomba fire certificate is needed. Confirm the approved plan with MBSA or MPHS.

Is a detached factory in Rawang or Shah Alam worth investing in?

It can be, provided you compare it only with other detached factories and check the papers. Over 24 months of JPPH-registered deals, the median detached factory sold for RM16 million on 67,901 sq ft of land in Shah Alam, RM6.92 million on 26,215 sq ft in Rawang and Kundang, and RM8.65 million on 49,744 sq ft in the Serendah area. Registered rents were RM1.50 psf a month in Shah Alam and RM1.06 in the Serendah area. Confirm the approved plan and CF or CCC with MBSA, MPS or MPHS.

What industries are suitable for a semi-D factory in Rawang or Kundang?

It suits SME manufacturing that runs its own lorries and needs a small office. The 2016 Selangor manual set a minimum semi-D lot of 60 ft x 132 ft, with at least two lorry bays and up to 30% of the gross floor area as office. Rawang and Kundang recorded 129 semi-D deals in 24 months, and Kota Elmina was the most active park in those records. Check the approved plan and CF or CCC with MPS. I also cover the Saujana Teknologi estate in Rawang on its own page.

Are semi-D factories in Shah Alam easy to rent out?

The registered records point to steady demand, though the evidence is thin. JPPH recorded 24 semi-D tenancies in Shah Alam over 24 months at a median of RM2.12 psf a month, about RM17,300 for 8,810 sq ft, which is more than in Rawang and Kundang, where there was no separate semi-D rent figure. Check the approved use and CF or CCC with MBSA, and ask the landlord for the latest TNB bill.

In Rawang or Serendah, which is more worth buying, a terrace factory or a semi-D factory?

That depends on your budget and how many lorries you run. In the Serendah area, JPPH registered 256 terrace factories against 28 semi-D over 24 months, with a median terrace sale of RM245,000. A terrace lot is at least 20 ft x 80 ft and shares one lorry bay per five units, while a semi-D has its own compound with at least two lorry bays. Check the approved plan and CF or CCC with MPHS.

Offices, layout and room to expand

Where can I find factories for rent with offices in Rawang, Serendah or Shah Alam?

There are factories with offices in all three areas, but the usual type differs. In Rawang and Kundang most are semi-D factories, where the 2016 Selangor manual allows up to 30% of the gross floor area as office. Shah Alam has terrace, semi-D and detached units, while the Serendah area, including Bukit Beruntung, is mostly terrace factories. Whichever you view, check that the approved plan shows the office, and ask the landlord for the CF or CCC.

How do I judge whether a factory in Rawang or Serendah is suitable for future expansion?

Look first at how much land is left around the building and how much building cover the approved plan allows. The 2016 Selangor manual let semi-D and detached factories cover up to 60% of the lot, so a detached factory with a large yard has far more room to extend than a terrace unit on a 20 ft x 80 ft lot. Check the approved building plan against the council's current guidelines, since PLANMalaysia@Selangor has issued newer editions, and confirm with TNB that the supply can carry any extra machines.

How should I allocate production area and office area in a factory in Shah Alam or Rawang?

In a detached or semi-D factory, the 2016 Selangor planning manual allowed up to 30% of the gross floor area to count as office, so keep the office within that share and leave the rest for machines and the paths between them. A terrace factory on a 20 ft x 80 ft lot is tighter, so make sure the approved plan actually shows the office layout. Before renovating, check the current guidelines with MBSA or MPS.

  • Single Storey vs Double Storey Factory: which is better? Neither wins in every case: it depends on floor loads, goods lift rules, sprinkler thresholds, how much office you need and property value. More on FactoryHub

To weigh a detached, semi-D or terrace factory in Rawang, Serendah or Shah Alam against your own process, WhatsApp Jason Low (Probationary Estate Agent PEA 1478, CID Realtors Sdn Bhd E(1) 1855) on +60 12-288 1834.

Questions people ask

01What does detached factory mean?+

A detached factory is a factory building that stands alone on its own lot and shares no wall with a neighbour. Selangor's 2016 planning manual set a minimum lot of half an acre for a small detached factory and one acre for a medium or large one, with setbacks of 40 ft facing a road and 25 ft at the sides and back. The yard around the building gives room for trailers, a substation and later extensions.

02What is a semi-D factory?+

A semi-D (semi-detached) factory is one of a pair of buildings that share a single wall, each on its own lot. The 2016 Selangor manual set a minimum semi-D lot of 60 ft x 132 ft, about 7,920 sq ft, with up to 60% of the lot built on and at least two lorry bays. In JPPH-registered deals, the median semi-D in Rawang and Kundang sold for RM4.3 million on 12,561 sq ft of land.

03Is a link factory the same as a terrace factory?+

Yes. Link factory is another name for a terrace factory, a unit in a row that shares walls with the units on both sides. The 2016 Selangor manual set a minimum terrace lot of 20 ft x 80 ft and a maximum height of 40 ft, with one lorry bay for every five units. In the Serendah area, which includes Bukit Beruntung, the registered median terrace factory sold for RM245,000.

04Can a 40-foot container be loaded at a terrace factory?+

Usually from the road or the apron, not inside the lot. The 2016 manual sized a trailer bay at 14 ft x 59 ft plus 18 m to manoeuvre, about 118 ft of depth in all, while the minimum terrace lot is 80 ft deep. If containers come every day, a semi-D or detached factory with its own yard is the safer choice.

05Is a semi-D factory cheaper per square foot than a detached one?+

Registered sale psf is per sq ft of land, and a detached lot carries much more yard, so comparing psf across types misleads. In Shah Alam the registered medians were RM514 psf of land for a semi-D and RM335 for a detached factory, but RM5.92 million against RM16 million in total. Compare the total price with the floor and yard you actually need.

06Does a semi-D factory need its own TNB substation?+

Only if your maximum demand calls for one. TNB's handbook requires a direct cable from a new substation above 350 kVA, about 505A at 400V, and the owner provides the substation land to TNB by transfer or lease at a nominal RM10. Below that, supply comes from the existing network, a feeder pillar or an existing substation, subject to TNB's study.

Sources

  1. PLANMalaysia@Selangor (JPBD Selangor): Manual Garis Panduan dan Piawaian Perancangan Negeri Selangor, editions approved 2016 and 2022, and the 2025 state planning guidelines (approved 7 November 2025, confirmed 12 November 2025)
  2. Manual Garis Panduan dan Piawaian Perancangan Negeri Selangor, third edition (2016), industrial chapter IND1 to IND3: lot sizes, setbacks, plinth, lorry bays, trailer bays, buffer zones, structures allowed in setbacks (copy hosted by REHDA Institute)
  3. Selangor State Assembly: written answer No. 346, Appendix A, industrial areas by local authority (2025)
  4. TNB: Electricity Supply Application Handbook (ESAH 3.1), Table 3-1 minimum supply schemes and substation land
  5. Palcon: Perakuan Bomba, schedule of designated premises under P.U.(A) 289/2020
  6. FactoryHub: Rawang and Kundang JPPH-registered transactions
  7. FactoryHub: Serendah JPPH-registered transactions
  8. FactoryHub: Shah Alam JPPH-registered transactions

Units on the market nearby

More on choosing an area or industrial park

All guides: Choosing an area or industrial park →

Probationary Estate Agent · PEA 1478 · CID Realtors Sdn Bhd E(1) 1855About Jason → · Contact →
Ask Jason about this