Before You Buy Industrial Land to Build a Factory in Rawang, Serendah or Shah Alam: Conversion, Access, Utilities, Soil, Filling, Slopes, Rivers and Flood Level
Before paying a deposit, check four things: an industry (Perusahaan) title and a local plan allowing your industry class; registered road access and a TNB power and water route; soil investigation and level survey for piling and filling cost; and river reserves, slopes of 25 degrees or more and the 100-year flood level, which decide your buildable area.
Key Takeaways
- The title decides the use, not the listing. Under the National Land Code every title carries one of three categories (agriculture, building or industry), and land in the industry category comes with implied conditions, including that the industry must start operating within three years of the relevant date.
- Land with no power or water can still be built on, but you pay for the route in. Above 350 kVA, TNB's handbook calls for a new substation on land you hand over at a nominal RM10, and Air Selangor can charge a capital contribution in three stages.
- The flood level sets the filling bill. MSMA requires building platforms above the 100-year flood level, and the JPS submission checklist adds 0.5 m of freeboard. Get cut and fill volumes from a licensed surveyor before you agree a price.
- Slopes of 25 degrees and steeper (Class III and IV) and any river or drain beside the lot take usable area away. JPS river reserves run from 5 m to 50 m on each bank, and Selangor adds building setbacks behind the reserve.
- Banks do lend on vacant industrial land. CIMB's vacant land financing, for example, offers up to 70% for commercial or industrial land over at most 20 years.
Is the land converted to industry, and what does the local plan allow?
When a client asks me to look at a plot in Rawang, Serendah or Sungai Choh, the official title search comes first, before any site visit. Section 52 of the National Land Code sets three categories of land use, and the category is endorsed on the title. If it reads "Perusahaan" or "Industri", the land is already industrial. Section 117 then adds implied conditions: the land may only be used for factories, workshops, warehouses and similar buildings for manufacturing, processing, storage or distribution, and the industry must begin operating within three years of the relevant date. If you plan to buy now and build later, ask the land office how that condition applies to your lot.
If the title still reads agriculture, only the registered proprietor can apply to change it under section 124. In practice the seller applies, or the sale agreement makes approval a condition. I explain that process, the premium and the Malay reserve and estate land traps in buying industrial land in Serendah or Batang Kali, so I will not repeat it here.
A converted title is still not planning permission. Three more checks:
- Which council. The Majlis Perbandaran Selayang (MPS) area covers Mukim Rawang, Mukim Batu and Mukim Setapak. Serendah, Sungai Choh, Bukit Beruntung and Batang Kali are in Hulu Selangor, under MPHS, and Shah Alam is under MBSA. Read the mukim on the title, not the town name on the listing.
- The local plan zone and the class of industry. MPS's own earthworks application form sends consultants to the council geoportal to identify the planning block. A lot zoned for light industry will not take a heavy process. See light, medium and heavy industry zoning in my areas and Ms Teh's light, medium and heavy industry guide.
- Express conditions. Some titles name a specific use. A food plant on a title that names another industry still needs an amendment.
Ready-infrastructure land or raw land?
A plot in a developer's industrial park usually comes with the roads, drains, retention ponds and utility reserves already planned. UMW's June 2024 briefing to MIDA on its 861-acre park in Serendah lists "ready-to-go infrastructure" as a key feature, and its master plan marks a main intake substation (PMU), a distribution substation (PPU), a retention pond, a water suction tank and a 60 m TNB reserve. On a raw estate lot, you or the seller provide those yourselves, and each one takes land and time. I cover that park in my UMW HVM Park guide.
Does the lot have legal road access, and can a 40-footer get in?
Look at the certified plan, not the track you drove in on. Section 284 of the National Land Code says no easement can be acquired by prescription, that is, by long and uninterrupted use. A lorry route over the neighbour's land gives you no right, even after twenty years of use, unless it is granted expressly and registered. If the lot is land-locked, the access must be negotiated and registered before you pay the balance.
If the only way in crosses a monsoon drain or a stream, the culvert or bridge needs technical approval. MPS's earthworks form lists JPS, JKR and, where relevant, Lembaga Urus Air Selangor (LUAS) among the agencies that comment on earthworks plans. For turning circles, gate widths and loading bays, see my guide to 40-footer truck access.
What if the land has no power or water yet?
You can build on a plot with no supply yet, but the cost and the land you give up depend on your load.
Power. TNB's Electricity Supply Application Handbook sets the minimum supply scheme by maximum demand:
| Maximum demand | Minimum supply scheme in the handbook |
|---|---|
| More than 100 kVA to 350 kVA | 400V underground cable from a feeder pillar or a new or existing substation |
| More than 350 kVA to 1,000 kVA | 400V direct underground cable from a new substation |
| 1,000 kVA up to under 5,000 kVA | Fed directly at 11kV through a switching station; additional PPU land may be needed |
The applicant provides the substation land and building to TNB, by transfer or lease at a nominal RM10. The title should be transferred before handover; without it, the applicant gives TNB a 12-month bank guarantee, renewed until the transfer or lease is registered. TNB may also use that substation to supply other consumers. Selangor's planning standards manual sizes the plots: 55 ft x 45 ft (16.5 m x 13.5 m) for a single chamber substation, 66 ft x 45 ft (20 m x 13.5 m) for a double chamber, and 150 ft x 150 ft (45 m x 45 m) for a PPU. Development next to a TNB transmission line reserve needs TNB Selangor's approval. More in TNB compact substations for a factory.
Water. Under the Water Services Industry (Water Services Deposits, Fees and Charges) Regulations 2014, a developer or owner connecting to the public main may be charged a capital contribution, paid 10% when the external reticulation plans are approved, 30% within nine months after that approval, and the balance on connection. The Fifth Schedule estimates average daily demand at 33,000 litres per hectare for light industry buildings, 50,000 for medium and 65,000 for heavy. Ask Air Selangor for the current assessment on your lot. If a water main runs through the plot, Air Selangor's pipe alignment procedure reviews it before the council issues a work permit, and the developer carries out any relocation.
Sewerage. The same Selangor manual requires a development above 150 population equivalent to provide a treatment plant or connect to the public sewer. Below that, with no sewer nearby, a septic tank is allowed.
Is a soil investigation needed, and what is the ground like?
No law makes you bore holes before you buy. The councils, however, ask for the results before they approve the works. The MPS earthworks checklist asks for a soil investigation (SI) report where relevant, including cross sections of slopes, cuts and fills, plus a slope stability or geotechnical report for Class III and IV land and a hydraulic report. Your engineer also needs the SI to design the piles. I cover piling and settlement checks on soft ground in my guide to Pulau Indah factories on soft ground.
The ground varies across my areas. Rawang and Kundang were tin-mining country: Media Selangor describes Tasik Biru Kundang as a former tin mining area. On old mining land, only boreholes tell you whether a pond was backfilled and how deep the piles must go. Low land near rivers can hold soft clay. Hilly lots in Hulu Selangor need the slope reports below.
What I suggest to buyers:
- Ask the seller for any earlier SI report, survey or approved earthworks plan.
- If there is none, ask for written permission to bore before the balance is due, or make the purchase conditional on the result.
- Get quotes from geotechnical contractors. The cost varies with the number of boreholes and their depth, so ask your engineer to set the scope first.
How much does filling cost, and which earthworks permits apply?
No council or agency publishes a rate per cubic metre, so I never quote one. The bill depends on the difference between today's ground level and the platform level you must reach, the lot area, whether fill is brought in, compaction, retaining walls and temporary drainage. Ask a licensed land surveyor for a level survey and cut and fill volumes, then ask contractors to price those volumes.
The platform level usually comes from the flood level. The MSMA 2nd Edition requires building platform levels above the 100-year ARI flood level, sets industrial drainage at 10-year ARI for the minor system and 100-year for the major system, and requires post-development peak flow to be no more than pre-development flow. The JPS submission checklist adds 0.5 m of freeboard above the 100-year level. That flow rule means a detention pond or on-site storage, which also takes land.
Permits follow the council's earthworks by-laws:
- MPS (Rawang): under the Earthworks By-laws (MPS) 2007, a minor earthworks route exists for a single detached factory on land with an approved master plan and existing infrastructure, where filling and cutting do not exceed 3 m. Beyond that, a full earthworks plan application needs a licensed surveyor's survey plan, the earthworks plan, a traffic management plan, a temporary drainage plan and an erosion and sediment control plan (ESCP) for JPS, plus a processing fee and a deposit.
- MPHS (Serendah, Sungai Choh, Bukit Beruntung, Batang Kali): under the Earthworks By-laws (MPHS) 2007, minor earthworks are certified on Form D by a registered engineer, and the form states that the exemption does not release the owner from liability for any loss the works cause.
Can you build on a sloping lot?
Yes, within limits. The PLANMalaysia guideline for hill and highland development groups land into Class I (under 15 degrees), Class II (15 to 25), Class III (25 to 35) and Class IV (35 and steeper). For land steeper than 25 degrees, the Selangor manual refers applicants to the state's own hill guideline (second edition, 2015) and asks for a geotechnical and slope stability report, terrain geological mapping by a registered geologist, an MSMA drainage report, an earthworks plan by a registered engineer, and an EIA for development above 20 hectares.
The EIA Order 2015 adds its own triggers: development or land clearing of an area with slopes of 25 degrees or more but under 35 needs an EIA, with public display once it covers 50% or more of the area, and an industrial estate of 20 hectares or more needs one too. Near a cut or natural slope steeper than 70 degrees, the PLANMalaysia guideline keeps buildings at least twice the slope height from the foot of an unstabilised slope, and at least once the height from the crest where stabilisation works are done. On a hilly lot, I ask the surveyor to mark the Class III and IV areas before anyone talks about price per square foot.
What does a river or drain beside the lot take away?
The JPS guideline on development involving rivers and river reserves sets minimum reserves measured from each bank:
| Width between banks | Reserve on each bank |
|---|---|
| More than 40 m | 50 m |
| 20 to 40 m | 40 m |
| 10 to 20 m | 20 m |
| 5 to 10 m | 10 m |
| Under 5 m | 5 m |
A lined channel keeps a minimum of 5.0 m on each side. The Selangor manual reads this together with the river reserve gazette under the National Land Code of 5 June 2009 and the LUAS Enactment 1999. It does not allow buildings, infrastructure or utilities inside the reserve, allows a river to be realigned only with JPS approval, and sets building setbacks behind the reserve: 40 ft (12.2 m) for a double-frontage building that faces the river, made up of a 20 ft walkway and a 20 ft setback, or 70 ft (21 m) where a service road runs along the bank. A lot sold by its title area can lose a strip along the stream, so I ask the surveyor to plot the reserve and setbacks before the client compares prices. For flood records, floor levels and drains around a lot, see my guide to checking a factory's flood risk.
Can industrial land be financed, and what does it sell for?
Yes. CIMB's vacant land financing offers up to 70% for commercial or industrial land over 5 to 20 years (or to age 65), for individuals aged 18 and above, and not for foreign applicants. Companies look at business property financing instead; CIMB's SME BizProperty financing, for example, lists vacant land among the eligible properties. Ask the bank before you sign whether it will accept the title as it stands, especially if conversion is still pending. For holding costs and loans on land you will not build on yet, read industrial land investment.
JPPH-registered transactions give a price check. In Rawang and Kundang, 116 industrial land deals were recorded in 24 months at a median price of RM2.6 million and RM57 psf of land. In Serendah, 72 deals at a median of RM2.47 million and RM37 psf of land, against RM32 psf for Hulu Selangor District. Shah Alam recorded only 6 industrial land deals, at a median of RM20.77 million and RM210 psf of land. Compare those figures against the usable area after reserves, substation land and detention ponds, not the title area. Current plots are on my Rawang, Serendah and Shah Alam land pages.
My checklist before a client pays the deposit
- Official title search: category, express conditions, restrictions, tenure, charges and caveats.
- Mukim, council and local plan zone, and whether your class of industry fits.
- Certified plan: road frontage, or a registered easement if access crosses other land.
- TNB: nearest supply, any transmission line reserve on or beside the lot, and where a substation would sit.
- Water main and sewer: distance to the tapping point, any pipe crossing the lot.
- Level survey and the 100-year flood level, so the platform height and fill volume are known.
- Existing SI report, or permission to bore before the balance.
- Slope classes on the survey, and any Class III or IV areas.
- River and drain reserves plus setbacks drawn on the plan.
- Usable area after all of the above, and the bank's view of the title.
If the land fails items 1 to 3, I tell the client to stop there. Whether it is a build or buy decision or a plot you have already found, I am happy to walk the site with you.
Send me the lot number or the listing, and I will go through these checks with you before you pay a deposit: WhatsApp Jason Low, Probationary Estate Agent PEA 1478 with CID Realtors Sdn Bhd E(1) 1855, on +60 12-288 1834.
Caveats on the title
How can I check if a factory in Rawang or Serendah has a caveat on its title?
Order an official title search at the land office for the factory lot. The search lists the title category, express conditions, restrictions, tenure, any charge and any caveat lodged against the land. For a lot under MPS (Rawang) or MPHS (Serendah), confirm the mukim and the local plan zone at the same time, and ask the seller for an up to date search before you pay the deposit.
Questions people ask
01What should I check when buying industrial land in Rawang or Serendah?+
Start with an official title search: the category should read industry and the express conditions should allow your use. Then confirm the council and local plan zone, legal road access on the certified plan, the TNB and water route, a level survey against the 100-year flood level, slope classes and any river reserve. Price the land on the usable area that remains.
02What is the difference between converted industrial land and agricultural land?+
Converted land has the industry category (Perusahaan) endorsed on its title and can be used for factories and warehouses under section 117 of the National Land Code. Agricultural land needs a section 124 conversion first, which only the registered proprietor can apply for and which usually comes with a premium. A converted title still needs planning permission from the council before you build.
03Can I buy industrial land that has no electricity or water yet?+
Yes, but build the connection costs into your price. TNB's handbook calls for a new substation above 350 kVA, on land handed to TNB at a nominal RM10, and Air Selangor can charge a capital contribution paid 10%, then 30%, then the balance on connection. Ask TNB and Air Selangor for their assessment before you sign.
04Is a soil investigation needed before buying industrial land?+
No law requires it before purchase, but the council asks for soil and slope reports with the earthworks plan, and your engineer needs the results to design the piles. On former tin-mining land around Rawang and Kundang, boreholes are the only way to know how deep the piles must go. Ask the seller for written permission to bore before the balance is due.
05How much does it cost to fill industrial land?+
No council or agency publishes a rate. The cost depends on how far the ground sits below the required platform, which MSMA sets above the 100-year flood level, plus the lot area, imported fill, compaction and retaining walls. Ask a licensed surveyor for cut and fill volumes and get contractors to price them.
06Can a bank finance industrial land?+
Yes. CIMB's vacant land financing, for example, lends up to 70% on commercial or industrial land for 5 to 20 years, to individuals aged 18 and above but not to foreign applicants. Companies use business property financing instead. Confirm with the bank that it accepts the title as it stands, especially if conversion is still pending.
07What are plot ratio and site coverage for a factory in Shah Alam or Rawang?+
Plot ratio is the factory's total floor area divided by the land area, and site coverage is the building footprint divided by the land area. The local plan and the council set both: MBSA in Shah Alam and MPS in Rawang. Before the design starts, read the approved planning permission and the conditions on the title.
08What does the industrial use on a factory title deed in Rawang mean?+
It means the title carries the industry category under section 52 of the National Land Code, and section 117 lets the land be used for factories, workshops and warehouses. One implied condition is that the industry must begin operating within three years of the relevant date. Even with a converted title, you still need planning permission from MPS or MPHS before you build.
Sources
- National Land Code (Act 828, Revised 2020), sections 52, 117, 124 and 284
- MPS: administrative area (Mukim Rawang, Batu, Setapak)
- MPS: Permohonan Pelan Kerja Tanah, OSC form and checklist (April 2026)
- MPS: Borang Permohonan Kerja Tanah, Undang-Undang Kecil Kerja Tanah (MPS) 2007
- MPHS: Borang D, Perakuan Kerja Tanah Kecil, Undang-Undang Kecil Kerja Tanah (MPHS) 2007
- Manual Garis Panduan dan Piawaian Perancangan Negeri Selangor, Edisi Ketiga (AS1, AS5, PE1, PE2, SP1)
- PLANMalaysia: Garis Panduan Perancangan Pembangunan di Kawasan Bukit dan Tanah Tinggi
- JPS: Garispanduan Pembangunan Melibatkan Sungai dan Rizab Sungai
- JPS: Urban Stormwater Management Manual for Malaysia (MSMA 2nd Edition, 2012)
- JPS: Submission Checklist for Stormwater Management in Malaysia
- DOE: Environmental Quality (Prescribed Activities) (EIA) Order 2015
- TNB: Electricity Supply Application Handbook (ESAH 3.1)
- Water Services Industry (Water Services Deposits, Fees and Charges) Regulations 2014, P.U. (A) 37
- Air Selangor: pipe and asset alignment review flow chart for developers
- MIDA: UMW High Value Manufacturing Park briefing slides (June 2024)
- Media Selangor: Terokai lokasi percutian tersembunyi di Selangor (23 May 2026)
- CIMB: Vacant Land Financing
- CIMB: SME BizProperty Financing
- FactoryHub: Rawang & Kundang JPPH-registered transaction prices
- FactoryHub: Serendah JPPH-registered transaction prices
- FactoryHub: Shah Alam JPPH-registered transaction prices
Units on the market nearby
Semi-D Factory for Rent in Saujana Teknologi Rawang, Rawang, 6,525 sq ft
RM 10,500/month
Semi-Detached Factory for Sale or Rent in Saujana Rawang, Rawang, 8,000 sq ft
RM 4,000,000 · RM 15,000/month
Detached Factory for Rent in Batu 17 Rawang, 9,000 sq ft
RM 21,000/month
More on buying a factory or industrial land
- Buying Industrial Land in Serendah or Batang Kali: Title Category, Land Conversion and Approvals to Check
- Industrial Building Inspection for a Used Factory in Rawang, Serendah or Shah Alam: Roof Leaks and Roof Life, Steel Rust, Asbestos, Termites, Fire Damage, Wiring and When to Pay for a Survey
- Is the Factory Asking Price Fair? Price per Square Foot, JPPH Deals and How Much to Negotiate in Rawang, Serendah and Shah Alam
- Bank Valuation Lower Than the Purchase Price, or Factory Loan Rejected? What to Do in Rawang, Serendah and Shah Alam